Jump pack peripheral - Revision history

Unknown user: /* Inclination Direction and Power (Byte 2) */

2023-01-01T07:55:55Z

Inclination Direction and Power (Byte 2)

← Older revision		Revision as of 07:55, 1 January 2023
Line 45:		Line 45:
	==== Inclination Direction and Power (Byte 2) ====		==== Inclination Direction and Power (Byte 2) ====

	* For the following, the value of X may be in the range [1,7] where 1 is low power and 7 is high power		* For the following, the value of P may be in the range [1,7] where 1 is low power and 7 is high power
	** ~~0xX0~~: single stable vibration (i.e. no inclination) at power X		** 0xP0: single stable vibration (i.e. no inclination) at power P
	** ~~0xX8~~: positive inclination (ramp up) from power X up to max		** 0xP8: positive inclination (ramp up) from power P up to max
	** ~~0x8X~~: negative inclination (ramp down) from power X down to min		** 0x8P: negative inclination (ramp down) from power P down to min
	* A value of 0x00, 0x08, or 0x80 immediately stops the currently executing vibration sequence		* A value of 0x00, 0x08, or 0x80 immediately stops the currently executing vibration sequence
	** Continuous vibration mode in mode byte must be disabled		** Continuous vibration mode in mode byte must be disabled

2023-01-01T07:42:59Z

Inclination Direction and Power (Byte 2)

← Older revision		Revision as of 07:42, 1 January 2023
Line 50:		Line 50:
	** 0x8X: negative inclination (ramp down) from power X down to min		** 0x8X: negative inclination (ramp down) from power X down to min
	* A value of 0x00, 0x08, or 0x80 immediately stops the currently executing vibration sequence		* A value of 0x00, 0x08, or 0x80 immediately stops the currently executing vibration sequence
	** Continuous vibration mode must be disabled		** Continuous vibration mode in mode byte must be disabled
	** Vibration source in ~~the next~~ byte must still be set		** Vibration source in mode byte must still be set

	There is a very noticeable change from one vibration power to the next when inclination is used and a long cycle period is selected.		There is a very noticeable change from one vibration power to the next when inclination is used and a long cycle period is selected.

2023-01-01T07:42:31Z

Inclination Direction and Power (Byte 2)

← Older revision		Revision as of 07:42, 1 January 2023
Line 51:		Line 51:
	* A value of 0x00, 0x08, or 0x80 immediately stops the currently executing vibration sequence		* A value of 0x00, 0x08, or 0x80 immediately stops the currently executing vibration sequence
	** Continuous vibration mode must be disabled		** Continuous vibration mode must be disabled
	** Vibration source in the next ~~word~~ must still be set		** Vibration source in the next byte must still be set

	There is a very noticeable change from one vibration power to the next when inclination is used and a long cycle period is selected.		There is a very noticeable change from one vibration power to the next when inclination is used and a long cycle period is selected.

2023-01-01T07:42:18Z

Inclination Direction and Power (Byte 2)

← Older revision		Revision as of 07:42, 1 January 2023
Line 49:		Line 49:
	** 0xX8: positive inclination (ramp up) from power X up to max		** 0xX8: positive inclination (ramp up) from power X up to max
	** 0x8X: negative inclination (ramp down) from power X down to min		** 0x8X: negative inclination (ramp down) from power X down to min
	* A value of 0x00, 0x08, or 0x80 immediately stops the currently executing vibration sequence ~~(continuous~~ vibration mode must be disabled)		* A value of 0x00, 0x08, or 0x80 immediately stops the currently executing vibration sequence
			** Continuous vibration mode must be disabled
			** Vibration source in the next word must still be set

	There is a very noticeable change from one vibration power to the next when inclination is used and a long cycle period is selected.		There is a very noticeable change from one vibration power to the next when inclination is used and a long cycle period is selected.

2023-01-01T07:40:48Z

← Older revision		Revision as of 07:40, 1 January 2023
Line 1:		Line 1:
	The jump pack acts as a sub-peripheral device on the [[Maple_bus\|Maple Bus]].		The jump pack acts as a sub-peripheral device on the [[Maple_bus\|Maple Bus]].

	~~'''NOTE:''' Some information here is misleading and/or incomplete~~

	== Vibration ==		== Vibration ==

2023-01-01T07:40:35Z

← Older revision		Revision as of 07:40, 1 January 2023
Line 18:		Line 18:
	=== Condition Word ===		=== Condition Word ===

	The following describes the layout of the condition word in the vibration "set condition" command.		The following describes the layout of the condition word in the vibration "set condition" command. Up to 15 words may be specified in order to set every vibration source as specified in the function definition.

	{\| class="wikitable"		{\| class="wikitable"

2023-01-01T07:35:44Z

Function Definition

← Older revision		Revision as of 07:35, 1 January 2023
Line 13:		Line 13:
	! Byte 0 (LSB) !! Byte 1 !! Byte 2 !! Byte 3 (MSB)		! Byte 0 (LSB) !! Byte 1 !! Byte 2 !! Byte 3 (MSB)
	\|-		\|-
	\| Number of ~~vibration~~ sources 1 to 15 (normally 1) \|\| Number of ~~concurrent~~ sources 1 to 15 (normally 1) ~~\|\| 0 \|\| 0~~		\| 0 \|\| 0 \|\| Number of concurrent sources 1 to 15 (normally 1) \|\| Number of vibration sources 1 to 15 (normally 1)
	\|}		\|}

2023-01-01T07:35:02Z

Function Definition

← Older revision		Revision as of 07:35, 1 January 2023
Line 13:		Line 13:
	! Byte 0 (LSB) !! Byte 1 !! Byte 2 !! Byte 3 (MSB)		! Byte 0 (LSB) !! Byte 1 !! Byte 2 !! Byte 3 (MSB)
	\|-		\|-
	\| Number of vibration sources (1 to 15) \|\| Number of concurrent sources (1 to 15) \|\| 0 \|\| 0		\| Number of vibration sources 1 to 15 (normally 1) \|\| Number of concurrent sources 1 to 15 (normally 1) \|\| 0 \|\| 0
	\|}		\|}

2023-01-01T07:33:56Z

← Older revision		Revision as of 07:33, 1 January 2023
Line 6:		Line 6:

	The "set condition" command (0x0E) with vibration function code and 1 condition word is used to activate vibration.		The "set condition" command (0x0E) with vibration function code and 1 condition word is used to activate vibration.

			=== Function Definition ===
			The function definition may be found in the peripheral's [[Maple_bus#Device_Info_Payload_Structure_.28cmd_0x05.29\|device info packet]].
			{\| class="wikitable"
			\|-
			! Byte 0 (LSB) !! Byte 1 !! Byte 2 !! Byte 3 (MSB)
			\|-
			\| Number of vibration sources (1 to 15) \|\| Number of concurrent sources (1 to 15) \|\| 0 \|\| 0
			\|}

	=== Condition Word ===		=== Condition Word ===

2023-01-01T07:23:55Z

Vibration Mode (Byte 3)

← Older revision		Revision as of 07:23, 1 January 2023
Line 54:		Line 54:
	! Bit 7 <br> (MSb) !! Bit 6 !! Bit 5 !! Bit 4 !! Bit 3 !! Bit 2 !! Bit 1 !! Bit 0 <br> (LSb)		! Bit 7 <br> (MSb) !! Bit 6 !! Bit 5 !! Bit 4 !! Bit 3 !! Bit 2 !! Bit 1 !! Bit 0 <br> (LSb)
	\|-		\|-
	\| colspan="4" \| vibration source 1 to 15<br>0 is invalid \|\| 0 \|\| 0 \|\| 0 \|\| continuous vibration mode<br>(1: enable)		\| colspan="4" \| vibration source 1 to 15 (usually 1)<br>0 is invalid \|\| 0 \|\| 0 \|\| 0 \|\| continuous vibration mode<br>(1: enable)
	\|}		\|}